303 E. Parson St. Galion, OH 44833    +1 (909)-996-3687    info@enerpatrecycling.com
 
Reliable, Durable & Efficient 
— Your Trusted One-Stop Recycling Equipment Partner
              
You are here: ENERPAT Home » News » Company News » Chaumont, France | Electric Motor Scrap Shredding & Separation System | Pre-Sales Site Assessment | ENERPAT

Chaumont, France | Electric Motor Scrap Shredding & Separation System | Pre-Sales Site Assessment | ENERPAT

Views: 0     Author: ENERPAT     Publish Time: 2026-11-17      Origin: Site

Inquire

1. On-Site Assessment for an Electric Motor Recycling Project

On November 3, 2026, the ENERPAT team visited a motor recycling facility in Chaumont, France, to assess the customer's requirements for upgrading its existing electric motor recycling operation.

The customer had already installed a primary processing line equipped with two 250 kW vertical hammer mills. The next objective was to develop a downstream processing section capable of further reducing the crushed motor scrap and separating valuable metals.

The main recovery targets are copper, aluminium and stainless steel. The customer is looking for a practical secondary shredding and metal separation solution that can improve material liberation and support the recovery of these metal fractions.

During the visit, the ENERPAT team reviewed the existing equipment, examined different categories of motor scrap and discussed the material characteristics that would influence the downstream system design.

Electric Motor Recycling Project

2. Existing Electric Motor Recycling Line and Project Requirements

The customer's current primary processing system consists of two 250 kW vertical hammer mills. The existing processing arrangement includes:

  • Belt conveyors

  • Feed hoppers

  • Vertical hammer mills

  • Magnetic separators

This primary stage reduces dismantled electric motors into smaller scrap fractions and removes ferrous materials through magnetic separation.

However, further processing is required to address the remaining mixed materials. The customer is particularly concerned with separating copper, aluminium and stainless steel from the crushed material, while plastic, rubber, textile and other non-metallic contaminants are not intended as target recovery products.

The proposed project therefore focuses on the section after primary hammer milling, with the following objectives:

  • Further reduce the size of the remaining motor scrap where necessary

  • Improve the liberation of copper wires, aluminium and stainless steel

  • Separate different metal fractions according to their physical properties

  • Reduce the carryover of non-metallic contaminants

  • Develop a downstream system compatible with the existing primary processing equipment

The final configuration will depend on the actual material condition after the first-stage hammer mills, rather than relying on equipment selection based on motor type alone.

3. Electric Motor Scrap Materials and Processing Requirements

During the site assessment, the customer introduced three categories of material requiring further processing. Their composition, physical condition and throughput requirements differ, so each stream needs to be considered separately during system design.

3.1 Large Motor Scrap – Material Type 1

Processing capacity: 250 kg/h

This material contains:

  • Aluminium

  • Stainless steel

  • Plastic and rubber

  • Copper wire ends

  • Iron screws

  • Dust

One notable copper component is approximately 100 mm long, 5 mm wide and 3 mm thick.

The mixture contains both metal and non-metallic components. The secondary processing stage needs to consider the size and shape of the copper pieces, as well as the presence of plastic, rubber and dust, when determining the appropriate size-reduction and separation methods.

Large Motor Scrap – Material Type 1

3.2 Large Motor Scrap – Material Type 2

Processing capacity: 250 kg/h

The second large-motor material stream mainly contains:

  • Copper wires

  • Aluminium

  • Stainless steel

  • Iron screws

  • Dust

The customer reported that the crushed material can become tangled. It also contains fine copper wires, oxidized aluminium, small amounts of textile fluff, copper chunks and iron pieces.

This material condition presents a separation challenge. Fine wires and irregular metal pieces may become entangled, making it more difficult to achieve consistent separation through a single processing stage.

The proposed solution needs to consider further material liberation and suitable separation stages to improve the recovery of copper and other target metals.

Large Motor Scrap – Material Type 2

3.3 Small Motor Scrap

Processing capacity: 2,500 kg/h

The small-motor stream has a higher processing capacity and a more varied material composition. The reported materials include:

  • Copper wires

  • Aluminium

  • Stainless steel

  • Iron screws

  • Plastic

  • Aluminium rods

  • Stainless steel strips

The copper wire diameter is approximately 1 mm. The customer specifically wants to process the recovered copper wires into copper granules.

After primary crushing, the material may form tangled clusters or ball-shaped masses. Other components and contaminants identified during the assessment include:

  • Incompletely crushed motor components

  • Rubber sealing rings

  • Old cloth and textile materials

  • Cast aluminium

  • Stainless steel rods

The fine copper wires and mixed metal shapes make this stream particularly important when evaluating the secondary shredding and separation process. The system must account for both material liberation and the customer's downstream copper granulation requirements.

Small Motor Scrap

4. Proposed Secondary Shredding and Metal Separation Solution

Based on the existing primary processing line and the three material categories, ENERPAT is evaluating a downstream solution combining secondary size reduction and metal separation.

The purpose is to process the material discharged from the existing vertical hammer mills and improve the separation of valuable metal fractions.

The final equipment arrangement will be determined after further technical evaluation and material testing. Depending on the actual particle size, metal shape and degree of material liberation, the following equipment and processes may be considered.

Secondary Shredder

A secondary shredder may be used to further reduce oversized or incompletely processed material and improve the consistency of the feed entering subsequent separation stages.

For this project, the selection of the shredding equipment needs to account for fine copper wires, tangled material, aluminium pieces and stainless steel components. The required output size and the material's physical condition will be important factors in determining the appropriate machine configuration.

Magnetic Separator

A magnetic separator can remove remaining ferrous materials, such as iron screws and other magnetic steel components, from the mixed scrap stream.

Removing ferrous contamination at the appropriate stage helps prepare the remaining non-ferrous and non-magnetic materials for further separation.

Eddy Current Separator

An eddy current separator may be considered for separating conductive non-ferrous metals from non-conductive materials.

It is commonly used in metal recycling systems to recover non-ferrous fractions such as aluminium. However, its suitability for this project will depend on the particle size, material shape and degree of liberation. It should not be treated as a standalone solution for separating copper from aluminium or stainless steel.

Copper Granulation and Recovery

For the small-motor material stream, the customer has a specific requirement to process approximately 1 mm copper wires into copper granules.

A copper granulator or copper wire granulation system may therefore be evaluated as part of the downstream recovery process. The appropriate configuration will depend on the condition of the copper wires after primary and secondary processing, including whether they remain tangled with other materials.

Stainless Steel Separation

Stainless steel is another important target material in this project. Since stainless steel is generally not separated by conventional magnetic and eddy current separation alone, additional sorting technology may need to be evaluated.

The appropriate method will depend on the stainless steel grade, particle dimensions, shape and degree of liberation. Representative material testing will help determine whether sensor-based or other dedicated sorting methods are required.

A System Designed Around the Actual Material

The objective is not simply to add more machines after the existing hammer mills. It is to develop a coordinated Electric Motor Recycling Line that addresses the different material characteristics and recovery requirements of each stream.

The proposed Metal Separation System will need to balance processing capacity, particle size, material liberation and separation performance. ENERPAT will use the customer's material samples and technical requirements to refine the equipment arrangement before finalizing the proposal.

5. Additional Application: Engine Cracker for Scrap Engine Recycling

In addition to electric motor recycling, ENERPAT also provides equipment for processing larger automotive components.

For recycling facilities handling complete end-of-life vehicle engines, engine blocks and gearboxes, the ENERPAT Engine Cracker offers a separate hydraulic pre-processing solution.

Designed for heavy scrap engine structures, the Engine Cracker uses hydraulic crushing force to break open engine assemblies and expose internal metal components. This helps prepare the material for subsequent metal recovery and sorting operations.

Although the French project discussed during this visit focuses on secondary shredding and metal separation of pre-crushed electric motor scrap, the Engine Cracker addresses a different material stream: larger, intact scrap engines and automotive components.

The choice between an Engine Cracker, an electric motor secondary shredding system or other recycling equipment depends on the incoming material and the required downstream process.

6. Technical Assessment and Project Planning

The site visit provided ENERPAT with a clearer understanding of the customer's existing production line, material composition and target recovery requirements.

Several technical factors will need to be addressed before the final solution is confirmed:

  • Different processing capacities across the three motor scrap categories

  • The presence of fine and tangled copper wires

  • The shape and dimensions of aluminium and stainless steel components

  • Remaining iron screws and other ferrous contaminants

  • Plastic, rubber, textile and dust contamination

  • The customer's requirement for copper granules from fine copper wires

  • The need to integrate the new downstream section with the existing 250 kW vertical hammer mills

The technical proposal will focus on a suitable combination of secondary shredding, material conveying and metal separation equipment. The final configuration and expected recovery results will need to be validated against representative material samples.

7. Project Follow-Up

Following the assessment, ENERPAT planned the next steps for technical communication and project development:

  1. Technical Proposal: Prepare the initial equipment proposal and workshop layout based on the information collected during the visit.

  2. Online Technical Meeting: Arrange a technical discussion with the customer to review the proposed process, equipment configuration and outstanding questions.

  3. Further Site Visit: Plan a return visit in the third week of November 2026 to continue technical discussions and advance commercial negotiations.

The project is at the solution evaluation stage. The next phase will focus on confirming the processing route and ensuring that the proposed equipment matches the customer's actual material and production requirements.

8. ENERPAT Electric Motor Recycling and Metal Separation Equipment

ENERPAT provides recycling equipment and integrated processing solutions for a range of metal recovery applications, including electric motor scrap, copper-bearing materials, aluminium scrap and other industrial metal waste.

Depending on the material and processing objectives, relevant equipment may include:

  • Vertical Hammer Mill – Primary size reduction of electric motor scrap

  • Secondary Shredder – Further size reduction and material liberation

  • Metal Shredder – Size reduction of various metal scrap materials

  • Magnetic Separator – Removal of ferrous contaminants

  • Eddy Current Separator – Recovery of suitable non-ferrous metal fractions

  • Copper Granulator – Processing copper wires into reusable copper granules

  • Copper Wire Granulation Line – Integrated processing of copper wire scrap

  • Engine Cracker – Hydraulic pre-processing of scrap engines and automotive components

  • Metal Separation System – Separation of different metal fractions in recycling operations

From individual machines to complete recycling systems, ENERPAT evaluates equipment selection according to material composition, required throughput, output specifications and the customer's existing production setup.

Planning an electric motor recycling or metal separation project?

Contact ENERPAT to discuss your material, processing capacity and target recovery requirements. Material testing and technical consultation can help determine a suitable equipment configuration for your operation.

Online Feedback
Enerpat is a global company specializing in waste-recycling and disposal solutions, with a mission to help customers build a better, more sustainable world. We are a leading global provider for municipal and industrial clients, helping them recycle and dispose of waste, reduce costs and consumption, and create more value.

We focus on sorters, shredders, balers, shears, and disposal equipment for a wide range of recycling needs. Enerpat believes that “Quality Transform The World.” We deliver the industry’s highest levels of quality and service. Choosing Enerpat means choosing trust and value.
 

Get To Know Us

Products

Contact Us

Tel:+1 (909)-996-3687
Tel:+1 (909)-996-3563
Email:info@enerpatrecycling.com
We Are Proud Members Of:
About Us
Copyright © 2024 ENERPAT AMERICA. All rights reserved.